PLCD79MP
INSTRUCTION MANUAL
VFD DISPLAY CD/CD-R/CD-RW/MP3 PLAYER
AM/FM-STEREO DIGITAL PLL TUNING RADIO
AND INFRARED REMOTE CONTROLLER
LOCATION AND FUNCTION OF CONTROLS
SPECIFICATION
GENERAL
Supply Voltage
Current Consumption
Power Output
Unit Dimensions
DC 13.8V. Negative Ground
Max.10A
25W X 4.
178[W] X 165[D] X 50[H] mm.
FM SECTION
Frequency range
Effective sensitivity
I.F Frequency
87.5MHz -107.9MHz
3uV.
10.7MHz.
AM SECTION
Frequency range
Effective sensitivity
I.F Frequency
530KHz - 1710KHz
40dB.
450KHz
RCA LINE OUT (OPTION)
Output
CD Max. 1200mv
CD PLAYER
System
Suitable CDs
Signal format
Compact Disc Audio System.
CD/CD-R/CD-RW/MP3 Disc
Sampling frequency 44.1KHz.
NO. of quantization bits 1bit.
20-100Hz <5dB
Frequency characteristics
1. OPEN BUTTON
10-20KHz <5dB.
50dB [1KHz]
2 STEREO channels.
Press the OPEN button to fold down the front control panel.
Then a CD can be inserted into the CD slot or ejected by pressing the EJ
button at the back of the front control panel.
S/N Ratio to CD
Number of channels
2.3. SEL BUTTON (Select) AND VOL(MENU)+/- KNOB
a) Press the SEL button briefly to select the mode of sound mode item by
item, such as VOLUME, BASS, TREBLE, BALANCE and FADER.
Now the settings of them can be adjusted by rotating the VOL + /- knob.
(Note: If equalizer settings such as POP and JAZZ have been selected
in DSP, it is impossible to change to BASS and TREBLE.)
b) Press the SEL button and hold for more than 1 second to access the
menu mode. Now press the SEL button briefly to select the menu mode
as follows: DSP (DSP OFF / POP M / JAZZ M / CLASS M / FLAT M),
BEEP ON/OFF, SEEK 1/2, VOL LAST/ADJ.
13
2
DSP
TROUBLE SHOOTING
In DSP mode you can select the equalizer settings POP M, JAZZ M,
CLASS M and FLAT M, and DSP OFF by rotating the VOL +/- knob.
BEEP ON/OFF
You can select two types of confirmation beep by rotating the VOL +/-
knob.
Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.
BEEP ON: The confirmation beep can be heard whenever a button is
pressed.
BEEP OFF: The confirmation beep is switch off.
SEEK 1/ 2 (only available during radio operation)
Common Symptoms
There is no power.
Cause
Solution
If the power supply is properly connected to
the car accessory, switch the ignition key to
" ON " or " ACC " .
The car ignition is switched off.
Seek function with the
You can select SEEK 1/ SEEK 2 by rotating the VOL +/- knob.
SEEK 1: Keep the or buttons pressed down and the radio will
stop at the next station that is detected.
or
buttons during radio operation.
Replace another fuse according to the wiring
diagram.
The fuse has blown.
The CDs cannot
be loaded.
Presence of CD disc inside the player Remove the disc in the player then put a new
upward
SEEK 2: As long as the
or
function will continue in the frequency band.
buttons are pressed down the search
The CDs are loaded The transport screws have not been
Remove the transport screws before using.
VOL LAST/VOL ADJ
only halfway into
the CD tray.
removed.
You can select VOL LAST or VOL ADJ mode by rotating the VOL +/- knob.
VOL LAST: The radio switches on at the actual volume it had when
it was last switched off.
VOL Addition: Rotating the VOL +/- knob you can pre-select a constant
switch-on volume.
Inserting the disc in upside down
Insert the compact disc with the label facing
upward
The device does
not work correctly
(EJECT, LOAD,
PLAY)
The surface of CD is extremely dirty
or it is damaged.
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.
4. POWER ON/OFF
Temperature inside the car is too
high.
Cool off until the ambient temperature returns
to normal
Turn the power on by using any button except the OPEN and REL button
and the VOL +/- knob on the front control panel; Press PWR button and
hold for approximate two seconds to turn power off.
Press the PWR button repeatedly to adjust the brightness of the VFD.
The volume control is set too low.
Turn up the volume properly.
There is no sound.
Check the power and earth connection
according to the wiring diagram.
The device has not been correctly
connected.
The operation keys
do not work
1.The built-in microcomputer is not
operating properly due to noise
2.Front panel is not properly fix into
its place
1. Switch the device off and on again. Or press
the RESET button to resume the program.
5. VFD Display
2. Reinstall the front panel
6.7. TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS
a) During RADIO mode:
The installation angle is more than
30 degrees
Adjust the installation angle to less than 30
degrees
press the
Press the
or
or
button briefly to tune a frequency manually.
button and hold for more than one second to start
The surface of the road is uneven.
Wait until the road becomes smoother before
playing the CD.
The sound of the
CD player skips
the automatic search for a radio station with a strong signal level.
(See also the function SEEK 1/SEEK 2.)
b) During CD/MP3 mode:
The surface of CD is extremely dirty
or it is damaged.
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.
press the
briefly to play the current track from the beginning of the current track.
button briefly to play next track. Press the
button
No radio reception.
The antenna cable is not connected.
Insert the antenna cable firmly into the
antenna socket of the device.
Press the
Press the
button twice continuously to play the previous track.
or button hold to skip forward or backward.
In automatic search The transmission signals are too
mode the radio does weak.
not stop at a trans-
Tune in to a radio station manually.
mitting station.
8. BAND BUTTON
Press the BND button briefly to select the radio broadcasting band you
would hear.
3
12
9. MODE BUTTON
Press the MODE button to select the CD/MP3 player or radio mode.
PRECAUTION OF DISC PLAY:
Cleaning the CD:
Before playing a CD, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc in the direction of the arrow.
10. MUTE BUTTON
Press the MU button to suppress the loudspeaker temporarily, and
press again to resume listening. The sound can also be resumed by
pressing the SEL, LD button or rotating the VOL +/- knob.
11. INFRARED REMOTE CONTROL SENSOR
12. A.P BUTTON (Auto-storage /Preset station memory scan)
a) Automatic store preset station memory:
During radio mode, press the A.P button and hold for longer than
one second to activate automatic station storage.
The radio searches within the current frequency band, and the six
strongest signal stations are allocate to the corresponding storage
locations each band. The stations that have now been stored will be
played for approximately five seconds each time, then the station
storage location is set. The radio will finish the searching for and
storage, the preset channel number and the frequency will appear
on the display.
Always insert the CD with the label side facing upwards.
If the CD is inserted with the printed side facing downwards, the device
may be damaged.
b) Automatic scan preset station memory:
After the A.P button has been pressed briefly, the radio scan all the
pre-set stations in the current frequency band. (FM 1, FM 2, FM 3,
MW 1, MW 2,)
Note: If there is already a CD in the CD slot, do not try to insert a
second CD. For this may damage the device.
Always hold CDs by the edge. In order to keep the CD clean do not touch
the surface. Pull out the CD as the direction of follows.
A.P button as a search function during MP3 playback:
a) Direct input the track number for CDs in MP3 format:
Press the A.P button once. The letters TRK SCH appear in the display.
Press the SEL button briefly. The letters TRK SCH 001 appear in the
display. The units place flashes.
Rotating the VOL +/- knob you can put in a track number from 0 to 9
in the units place.
Press the SEL button briefly once more. The tens place flashes.
Rotating the VOL +/- knob you can put in a track number from 0 to 9
in the tens place.
Press the SEL button briefly once more. The hundreds place flashes.
Rotating the VOL +/- knob to put in a track number from 0 to 9 in the
hundreds place if necessary.
press the SEL button and hold for 1 second to complete entry of the
track numbers. Immediately after this, the selected track is played.
Note: If the input track number is overrun the range, it will play the
last track in the current MP3 disc.
Do not attach any sticker or adhesive tape on the CD.
Do not expose the CD to direct sunlight or sources of heat such as
heating pipes.
Do not leave CDs in a car if it parked in direct sunlight as that will lead to
a considerable rise in the temperature inside the car.
b) File search function for CDs in MP3 format:
Note: Do not use any solvents such as petrol or thinning agents.
Commercially available cleaning substances or antistatic spray will damage
the device.
Press the A.P button twice. The letters FILE SCH appears in the display.
Press the SEL button briefly to show the first folder that has been
selected in the display.
Rotating the VOL +/- knob it is now possible to select the various folder
on the CD.
4
11
Press the SEL button and hold for 1 second. The selected folder is played
starting with the first song.
Then press the SEL button briefly and you can select a track in the folder
by rotating the VOL +/- knob.
INSTALLATION METHOD
Complete entry of the titles by pressing the SEL button for 1 second.
Immediately after this, the selected track is played.
c) Keyword search function for CDs in MP3 format:
Press the A.P button three times. The letters CHAR SCH appear in the
display.
Press the SEL button briefly. The letter A appears on the left of the dis-
play.
Then rotate the VOL +/- knob left or right to enter a letter from A to Z or
a number from 0 to 9, as well as blank character in the first position of
the display.
Press the SEL button briefly. An A appears in the second position of the
display.
Then rotate the VOL +/- knob left or right to enter a letter from A to Z or
a number from 0 to 9 as well as blank character in the second position
of the display.
In the same way, you can enter the character in the third, fourth, fifth,
...Xth position until you have entered your search term.
Note: The following letters and numbers or blank character are entered
from left to right. The last entry can be deleted by pressing the A.P button.
Complete entry of the search term by pressing the SEL button and hold
for 1 second. Immediately after this, the selected track is played.
13-18. PRESET STATION MEMORY AND TOP, INT, RPT, RDM BUTTONS
a) During radio mode:
Press the six buttons briefly directly selects a preset radio station.
If the six buttons are pressed for more than 2 seconds, the station
currently being listened to is memorized into the selected preset
button.
b) During CD/MP3 mode:
Press the TOP button briefly to interrupt the playback of the CD.
Press again to resume normal playback of the CD/MP3.
Press the TOP button and hold for approximately 2 seconds to play
the first track of the current disc.
Press the INT button to play the first 10 seconds part of each track.
Press again to stop scan, while the currently selected track will be
played.
Press the RPT button to play the current track repeatedly.
Press again to cancel this function.
Press the RDM button to play all tracks on disc in random.
Press again to cancel this function.
c) During the normal playback of CDs in MP3 format:
Press the radio preset button 5 and 6 to move up and down10 tracks
at a time.
5
10
19. CLOCK BUTTON
WIRING DIAGRAM
Press the CLK button briefly to display time on the display, then press
the CLK button and hold until the real time flashes on the display.
Rotate the VOL +/- knob left to adjust HOUR. Rotate the VOL +/- knob
right to adjust MINUTE.
ANTENNA PLUG
VFD TRANSFORMER
20. LOUDNESS BUTTON
FUSE 10A
YELLOW
AUX LINE IN
RED R
CONSTANT B+
Press the LD button to enhance the bass effect when the volume level is
low. Press again to cancel the loudness effect.
WHITE
L
L
BLACK(GND)
FUSE 0.5A
FUSE 0.5A
RED R
WHITE
ACC RED (B+)
RCA OUTPUT LINE
GREY
21. ST/MO BUTTON
BLUE AUTO ANT
During radio mode, press the ST briefly to select stereo or mono sound
mode.
+
FRONT
RIGHT
+
WHITE
FRONT
-
WHITE/BLACK
GREEN
GREY/BLACK
VIOLET
-
LEFT
22. RELEASE BUTTON
LOUDSPEAKER
+
LOUDSPEAKER
+
To remove the front control panel from the main body, press the REL
button to eject the front control panel.
REAR
REAR
GREEN/BLACK
VIOLET/BLACK
-
-
Note:
23. EJECT KEY
1.Make sure use a speaker with 4 ohm load impedance.
2.Do not make the auto antenna wire and ground touch each other.
Press this key to eject the CD.
24. CD SLOT
CAUTION:
In order to protect power IC from being burnt out during installation the car stereo,
it is necessary to follow the steps below to connect the wires during installation:
25. FLASHING LED
When the front control panel is removed this indicator flashes.
Step 1: Connect the ground wire (Black);
Step 2: Connect all speaker wires and power antenna wire (Blue):
26. RESET BUTTON
Push this button with a cuspidal object to renovate the distorted
program once the program is distorted.
Note: Before operating the unit for the first time, or after replacing
the car battery or changing the connections. You must reset the unit.
Push this button with a cuspidal object. This operation will erase the
clock setting and some stored contents.
Left speaker
Right speaker
Front speaker: White (+) White/Black (-)
Rear speaker: Green (+) Green/Black (-)
Grey (+)
Violet (+)
Grey/Black (-)
Violet/Black (-)
Step 3: RCA Line Out (R- Red/ L-White).
Step 4: AUX Line in ( R-Red/L-White).
Note: This AUX Line in for video system audio input.
Step 5: Connect Back up (Yellow) and Acc wire (Red)
9
6
OPERATION OF REMOTE CONTROL:
The Maintenance of Remote Control
Note:
REPLACE THE BATTERY OF REMOTE CONTROL:
Before use this remote control, please make sure
turn on the device by pressing the power button on
the front control panel.
1.Remove the battery holder as the direction indicated by the arrow.
2.Replace the battery, Set a new battery properly with (+) side up.
3.Insert the battery holder. Push in the holder to the original position.
1. Power On/Off.
2. Mute Button
3. Loudness Button
4. Level/MENU UP Button
5. SEL/MENU Button
6. Level/MENU Down Button
BATTERY INFORMATION:
Designated Battery: CR2025 3V
Battery Life: 6 months with normal use in normal room temperature, and
the out of date battery must be immediately removed and disposed properly.
7. MO/ST Button
9.Band Button
8. A.P Button
10. Mode Button
CAUTION:
Improper use of batteries may cause overheating, explosion or ignition, and
resulting in jury or fire .
11.Tune/Seek Up And Track Skip Up/FF Button
12.Tune/Seek Down And Track Skip Down/REW Button
Battery leakage may cause damage to the unit.
Do not disassemble or short the batteries.
Do not throw the batteries into the fire.
13. SCAN BUTTON
Press the SCN button to scan the radio frequency. If a valid signal has
detected, the current frequency will be hold and blinked for 5 seconds,
then press SCN again to stop scan and remain the current frequency;
otherwise, the radio will go on to scan the other radio frequency fiver
seconds later.
To avoid the risk of accident, keep the batteries out of reach of children.
14. Clock Display /Setting Button
15. LO/DX Button
In radio mode, press it to change local reception or distance reception.
And the LOC will showing on the LCD display when the receiver detect
some signal of stable local station.
Note: This operation is only for FM reception. During AM mode, LOC is void.
16. CD Track TOP/ /Radio Preset 1
18. CD Track RPT/Radio Preset 3
20. Radio Preset 5
17. CD Track INT/Radio Preset 2
19. CD Track RDM/Radio Preset 4
21. Radio Preset 6
7
8
|